Flashings

Ridge pieces are used at the apex of the roof to join the two sides together. Cladco polyester paint coated flashing ridges are folded to a 130-degree internal angle and will flex 10–15 degrees either way, dependent on the angle of your roof. Metal roof flashing ridges are a major component in any profiled clad apex roof and are available in a range of colours and finishes to match our roofing sheets. Polyester paint coated ridge flashing will enhance the aesthetics of any building, providing the perfect finish.

Cladco Roof Ridge cap pieces are used at the apex of the roof to join the two sides together. They are folded to a 130-degree internal angle and will flex 10 – 15 degrees either way, dependent on the angle of your roof. Ridges are a major component in any profiled clad apex roof and as they are available in a range of colours and finishes to match our roof sheets, PVC ridge caps will enhance the aesthetics of any building.

Ridge pieces are used at the apex of the roof to join the two sides together. Cladco Ridges are folded to a 130-degree internal angle and will flex 10 – 15 degrees either way, dependent on the angle of your roof. Ridges area major component in any profiled clad apex roof and as they are available in a range of colours and finishes to match our roof sheets, they will enhance the aesthetics of any building.

Cladco 3m Galvanised Ridge Flashings are used to seal and finish an apex roof. Folded to a 130-degree internal angle, Ridge Flashings can be flexed 10-15 degrees either way depending on your roof’s angle. Cladco Flashings include a 10mm safety welt both sides.

Cladco Nordic Ridge Flashings are used at the apex of a roof to join two sides of a roof together. Polyester Paint Coated Nordic Ridge Flashings are folded to a 130-degree internal angle and will flex 10-15 degrees either way, depending on the angle of your roof. Our steel Nordic Ridges are available in a range of colours to match Polyester Paint Roofing Sheets.

Nordic Ridge Flashings are used at the apex of a roof to join two sides. PVC Plastisol Coating provides scratch resistance with a quality leathergrain finish. Nordic Ridge Flashings are folded to a 130-degree internal angle and will flex 10-15 degrees either way. PVC Plastisol Flashings are available in a range of colours to match our PVC Plastisol Roofing Sheets.

Finish your building with Cladco Nordic Ridge Flashings available with a Prelaq Mica coating. Nordic Ridge Flashings are installed at the top of your roofing installation to cover the ridge gap between roof sheets. Choose from three colours to match Cladco Tile Form Sheets.

Ridge pieces are used at the apex of the roof to join the two sides together. Cladco galvanised finish coated flashing ridges are folded to a 130-degree internal angle and will flex 10 – 15 degrees either way, dependent on the angle of your roof. Metal roof flashing ridges are a major component in any profiled clad apex roof and are available in a range of colours and finishes to match our roofing sheets. Galvanised finish ridge flashing will enhance the aesthetics of any building, providing the perfect finish.

Ridge pieces are used at the apex of the roof to join the two sides together and provide wall flashing trim. Cladco galvanised steel flashing ridges are folded to a 130-degree internal angle and will flex 10 – 15 degrees either way, dependent on the angle of your roof. Metal roof flashing ridges are a major component in any profiled clad apex roof and are available in a range of colours and finishes to match our roofing sheets. Galvanised steel flashing will enhance the aesthetics of any building, providing the perfect finish.

Secure them by stitching them, using st22 stitching screws, to the roofing sheet below. Be sure to allow an overlap of a minimum of 200mm when fitting roof barge boards end to end.

Ridge flashings are used at the apex of the roof to join the two sides together. At Cladco, our ridge flashings are folded to a 130-degree internal angle and will flex 10 - 15 degrees either way, dependent on the angle of your roof. Ridges are a major component in any profiled clad apex roof and as they are available in a range of colours and finishes to match our roof sheets, they will enhance the aesthetics of any building. 

Used at the apex of your roofing to join the two sides together, Cladco ridge cover flashings are folded to a 130-degree angle and will flex 10 – 15 degrees either way, depending on your roof’s angle. Ridge cover flashings are an important component in any profiled clad apex roof and these prelaq mica ridge cover flashings are available in graphite grey and copper brown colours to match your roofing shoots.

Ridge flashings are used at the apex of the roof to join the two sides together. At Cladco, our ridge flashings are folded to a 130-degree internal angle and will flex 10 – 15 degrees either way, dependent on the angle of your roof. Ridges are a major component in any profiled clad apex roof, and they will enhance the aesthetics of any building, especially in galvanised.

Use roof barge flashing boards, or verges, at the end of a run of sheets to trim and seal off the edge of the roof. They help to weatherproof the building while adding to its appearance. We offer free samples of our roof barge flashing boards – click here for more information.

These 150 x 150mm flashings give a coverage of 142 x 142mm due to the 8mm welt. Secure the boards by stitching them to the roofing sheet below using st22 stitching screws and be sure to allow a minimum overlap of 200mm when fitting the roof barge boards end on end.

Barges, sometimes known as Verges, are used at the end of a run of sheets to trim and seal off the edge of the roof. All flashings are a vital part of any profiled clad roof, they not only help to weatherproof the building but also add to it aesthetically too.

Barges are available in a range of finishes and colours to match or contrast our roofing sheets depending on the look you are after. They are secured by stitching them (Using ST22 Stitching Screws) to the roofing sheet below. You will need to allow an overlap of a minimum 100mm when fitting barges end on end.

Steel Corner Barge Flashings are an important component in the cladding of a profiled roof installation, weatherproofing the building and improving its appearance. Our 150mm x 150mm Barge Flashings with a PVC Plastisol coating are available in a range of colours to match our range of Roofing Sheets.

Roof Barge boards, sometimes known as Verges, are used at the end of a run of sheets to trim and seal off the edge of the roof. All roof barge flashings are a vital part of any profiled clad roof; they not only help to weatherproof the building but also add to it aesthetically too.

Roof Barge Boards are available in a range of finishes and colours to match or contrast our roofing sheets, depending on the look you are after. They are secured by stitching them (using st22 stitching screws) to the roofing sheet below. You will need to allow an overlap of a minimum 100mm when fitting roof barge boards end on end.

Sometimes referred to as verges, roof edge barge flashings can be used at the end of a run of sheets and will seal off the edge. A vital part of any profiled clad roof, metal roof barge flashing helps to weatherproof a building and add an aesthetically pleasing element to your finished roof project.

These metal roof barge flashings are available in 150mm x 150mm, made from prelaq Mica and will match or contrast the look of your roof, depending on the look you’re after, available in graphite grey or copper brown. You can secure them to your roofing using stitching screws and will need to allow for an overlap of a minimum of 200mm when fitting end on end.

Each 90 degree Corner Flashing can be used at the end of a run of sheets to trim and seal off the edge of a roof. Steel Flashings are a vital part of any roofing or cladding project, helping to improve weatherproofing and aesthetics. Available in a range of colours to match or contrast Tile Form Roofing Sheets. Flashings are installed using 22mm Stitching Screws to the roofing sheets below. Allow a minimum 200mm overlap when fitting Corner Barge Flashings.

Corner barges flashings are used at the end of a run of sheets to trim and seal off the edge of the roof. All flashings are a vital part of any profiled clad roof as they not only help to weatherproof the building but also add to it aesthetically too. Order a sample of this product.

Our corner barges for sheet metal flashing has a galvanised steel finish that looks great or in contrast with our roofing sheets, depending on the look you’re after. You will need to allow an overlap of a minimum of 200mm when fitting barges end on end.

Cladco 3m 200mm x 200mm Barge Corner Flashings are available in a Galvanised finish. Corner Barge Flashings, sometimes known as verges, are used at the end of a run of sheets to tidy and seal off the edges of a roof. Secure Corner Barge Flashings with 22mm Stitching Screws to the sheets below.

3 metre Drip Tray Flashings by Cladco are made from quality steel and provides an efficient course for water to run-off your roof and above your windows and doors. Available in PVC, Polyester Paint and Prelaq Mica Colours and Coatings.

3m Abutment Flashings are manufactured to finish the adjoining edge of lean-to buildings, or other buildings, with an internal angle. Flashings are folded to create a 110-degree internal angle, with 10-15 degrees flex. Available in a smooth Polyester Paint coat, and in five colours, to match Cladco Roofing Sheets.

Cladco Abutment Flashings with a PVC Plastisol coat provide a durable, scratch-resistant finish for projects with an internal angle such as lean-to buildings. Made from multi-layered steel and with a PVC leather grain finish to complement Cladco Roofing Sheets, these Flashings are available in a wide choice of 11 colours. 

Prelaq Mica Abutment Flashings are made in 3m lengths from high-quality, coated steel. Complete the internal edge of a lean-to building, for example, with matching profiled Roofing Sheets. These Flashings are designed to flex 10-15 degrees either way from 110-degrees, and available in a choice of three colours: Black, Graphite Grey and Copper Brown.

Galvanised Abutment Flashings are produced to 200mm x 200mm widths and in 3m lengths. Flashings are folded with a 110-degree internal angle and can flex 10-15 degrees to suit your lean-to project, or similar building. Manufactured from Galvanised steel for a rust-resistant, metal finish.